Pontiac Keyless Entry Remote Fob Programming Instructions
Keyless Entry Remote Fob Programming Instructions Available for the following Pontiac models.
Click below to select your model.
| Model | Year | |
|---|---|---|
| Pontiac Aztek | 2001 | Programming Instructions |
| Pontiac Aztek | 2002 | Programming Instructions |
| Pontiac Aztek | 2003 | Programming Instructions |
| Pontiac Aztek | 2004 | Programming Instructions |
| Pontiac Aztek | 2005 | Programming Instructions |
2001 Pontiac Aztek Keyless Entry Remote Fob Programming Instructions
For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
- Close all doors.
- Press and hold the Unlock button on door lock switch on drivers door. Hold until instructed to release in step 6.
- Insert key into the ignition cylinder but do not turn it.
- Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
- Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
- Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
- Press both the Lock and Unlock buttons on the remote up to 30 seconds. A chime will sound 2 times if remote has programmed successful.
- Repeat step 7 if you are programming additional remotes.
- Remove key from ignition to exit programming mode.
NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.
2001 Pontiac Aztek Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2002 Pontiac Aztek Keyless Entry Remote Fob Programming Instructions
For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
- Close all doors.
- Press and hold the Unlock button on door lock switch on drivers door. Hold until instructed to release in step 6.
- Insert key into the ignition cylinder but do not turn it.
- Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
- Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
- Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
- Press both the Lock and Unlock buttons on the remote up to 30 seconds. A chime will sound 2 times if remote has programmed successful.
- Repeat step 7 if you are programming additional remotes.
- Remove key from ignition to exit programming mode.
NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.
2002 Pontiac Aztek Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2003 Pontiac Aztek Keyless Entry Remote Fob Programming Instructions
For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
- Close all doors.
- Press and hold the Unlock button on door lock switch on drivers door. Hold until instructed to release in step 6.
- Insert key into the ignition cylinder but do not turn it.
- Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
- Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
- Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
- Press both the Lock and Unlock buttons on the remote up to 30 seconds. A chime will sound 2 times if remote has programmed successful.
- Repeat step 7 if you are programming additional remotes.
- Remove key from ignition to exit programming mode.
NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.
2003 Pontiac Aztek Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2004 Pontiac Aztek Keyless Entry Remote Fob Programming Instructions
For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
- Close all doors.
- Press and hold the Unlock button on door lock switch on drivers door. Hold until instructed to release in step 6.
- Insert key into the ignition cylinder but do not turn it.
- Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
- Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
- Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
- Press both the Lock and Unlock buttons on the remote up to 30 seconds. A chime will sound 2 times if remote has programmed successful.
- Repeat step 7 if you are programming additional remotes.
- Remove key from ignition to exit programming mode.
NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.
2004 Pontiac Aztek Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2005 Pontiac Aztek Keyless Entry Remote Fob Programming Instructions
For Buick Rendezvous / Intrigue / AztekObtain all remote transmitters for this vehicle.
- Close all doors.
- Press and hold the Unlock button on door lock switch on drivers door. Hold until instructed to release in step 6.
- Insert key into the ignition cylinder but do not turn it.
- Remove key from ignition and then insert key into ignition without turning ignition cylinder and remove key.
- Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
- Release door lock switch on drivers door panel. A Chime will sound 3 times indicating that you are in programming mode.
- Press both the Lock and Unlock buttons on the remote up to 30 seconds. A chime will sound 2 times if remote has programmed successful.
- Repeat step 7 if you are programming additional remotes.
- Remove key from ignition to exit programming mode.
NOTE: If you are having trouble getting this procedure to work, we have found that some vehicles need step 3 to be done before step 2.
2005 Pontiac Aztek Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Pontiac Bonneville | 2000 | Programming Instructions |
| Pontiac Bonneville | 2001 | Programming Instructions |
| Pontiac Bonneville | 2002 | Programming Instructions |
| Pontiac Bonneville | 2003 | Programming Instructions |
| Pontiac Bonneville | 2004 | Programming Instructions |
| Pontiac Bonneville | 2005 | Programming Instructions |
2000 Pontiac Bonneville Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Pontiac Bonneville Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2001 Pontiac Bonneville Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Pontiac Bonneville Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2002 Pontiac Bonneville Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Pontiac Bonneville Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2003 Pontiac Bonneville Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Pontiac Bonneville Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2004 Pontiac Bonneville Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Pontiac Bonneville Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2005 Pontiac Bonneville Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Pontiac Bonneville Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Pontiac G5 | 2007 | Programming Instructions |
| Pontiac G5 | 2008 | Programming Instructions |
| Pontiac G5 | 2009 | Programming Instructions |
| Pontiac G5 | 2010 | Programming Instructions |
2007 Pontiac G5 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Pontiac G5 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Pontiac G5 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Pontiac G5 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Pontiac G5 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Pontiac G5 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Pontiac G5 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Pontiac G5 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Pontiac G6 | 2005 | Programming Instructions |
| Pontiac G6 | 2006 | Programming Instructions |
| Pontiac G6 | 2007 | Programming Instructions |
| Pontiac G6 | 2008 | Programming Instructions |
| Pontiac G6 | 2009 | Programming Instructions |
| Pontiac G6 | 2010 | Programming Instructions |
2005 Pontiac G6 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Pontiac G6 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2006 Pontiac G6 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Pontiac G6 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2007 Pontiac G6 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Pontiac G6 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Pontiac G6 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Pontiac G6 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Pontiac G6 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Pontiac G6 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Pontiac G6 Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Pontiac G6 Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, G5, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Pontiac Grand Am | 1994 | Programming Instructions |
| Pontiac Grand Am | 1995 | Programming Instructions |
| Pontiac Grand Am | 1996 | Programming Instructions |
| Pontiac Grand Am | 1997 | Programming Instructions |
| Pontiac Grand Am | 1998 | Programming Instructions |
| Pontiac Grand Am | 1999 | Programming Instructions |
| Pontiac Grand Am | 2000 | Programming Instructions |
| Pontiac Grand Am | 2001 | Programming Instructions |
| Pontiac Grand Am | 2002 | Programming Instructions |
| Pontiac Grand Am | 2003 | Programming Instructions |
| Pontiac Grand Am | 2004 | Programming Instructions |
| Pontiac Grand Am | 2005 | Programming Instructions |
1994 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
- Access the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has wires leading up to it and it is not connected to anything.)
- Jump programming connector terminals.
- System should now lock and unlock doors to indicate programming mode has been entered.
- Press any button on keyless remote once.System should now lock and unlock doors, indicating successful programming of keyless remote.
- Repeat step 4 for additional remote or other existing keyless remote.
- Remove programming connector jumper wire to exit programming mode.
- Test remote(s).
1994 Pontiac Grand Am Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1995 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
- Access the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has wires leading up to it and it is not connected to anything.)
- Jump programming connector terminals.
- System should now lock and unlock doors to indicate programming mode has been entered.
- Press any button on keyless remote once.System should now lock and unlock doors, indicating successful programming of keyless remote.
- Repeat step 4 for additional remote or other existing keyless remote.
- Remove programming connector jumper wire to exit programming mode.
- Test remote(s).
1995 Pontiac Grand Am Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1996 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
- Access the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has wires leading up to it and it is not connected to anything.)
- Jump programming connector terminals.
- System should now lock and unlock doors to indicate programming mode has been entered.
- Press any button on keyless remote once.System should now lock and unlock doors, indicating successful programming of keyless remote.
- Repeat step 4 for additional remote or other existing keyless remote.
- Remove programming connector jumper wire to exit programming mode.
- Test remote(s).
1996 Pontiac Grand Am Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1997 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
- Make sure ignition is in the OFF position.
- Locate the programming connector in the trunk (drivers side). It is a plastic connector with two wires leading up to it. The connector is not plugged into anything. You may have to pull back trim to access connector.
- The programming connector should have two terminals. Connect both terminals with a suitable jumper wire. Make sure the terminals remain connected throughout the programming procedure.
- Press the LOCK and UNLOCK buttons on the remote simultaneously. In response the Keyless Entry Module will cycle all the Door Lock Motors at once. Your new remote has been accepted and all existing remotes have been erased.
- Repeat the previous step for each additional remotes (including any existing remotes) Do not remove jumper wire in between programming of remotes.
- Remove the jumper wire from the Keyless Remote Connector.
1997 Pontiac Grand Am Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
- Make sure ignition is in the OFF position.
- Locate the programming connector in the trunk (drivers side). It is a plastic connector with two wires leading up to it. The connector is not plugged into anything. You may have to pull back trim to access connector.
- The programming connector should have two terminals. Connect both terminals with a suitable jumper wire. Make sure the terminals remain connected throughout the programming procedure.
- Press the LOCK and UNLOCK buttons on the remote simultaneously. In response the Keyless Entry Module will cycle all the Door Lock Motors at once. Your new remote has been accepted and all existing remotes have been erased.
- Repeat the previous step for each additional remotes (including any existing remotes) Do not remove jumper wire in between programming of remotes.
- Remove the jumper wire from the Keyless Remote Connector.
1998 Pontiac Grand Am Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
- Make sure ignition is in the OFF position.
- Locate the programming connector in the trunk (drivers side). It is a plastic connector with two wires leading up to it. The connector is not plugged into anything. You may have to pull back trim to access connector.
- The programming connector should have two terminals. Connect both terminals with a suitable jumper wire. Make sure the terminals remain connected throughout the programming procedure.
- Press the LOCK and UNLOCK buttons on the remote simultaneously. In response the Keyless Entry Module will cycle all the Door Lock Motors at once. Your new remote has been accepted and all existing remotes have been erased.
- Repeat the previous step for each additional remotes (including any existing remotes) Do not remove jumper wire in between programming of remotes.
- Remove the jumper wire from the Keyless Remote Connector.
1999 Pontiac Grand Am Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
- Close the vehicle doors.
- Turn ignition to the ON position then OFF.
- Remove key from the ignition.
- Press and hold the driver side door lock switch in the UNLOCK position until step 8.
- Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder)
- Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder)
- Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder) Leave key in the ignition cylinder.
- Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
- Press the LOCK and UNLOCK buttons together on the keyless remote and hold until the vehicle beeps twice to verify that the keyless remote has been successfully programmed. This may take approximately 15 seconds.
- Perform the previous step (9) to program up to four keyless remotes, including any old ones.
- Remove the ignition key to exit Program Mode.
2000 Pontiac Grand Am Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Pontiac Grand Am Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Pontiac Grand Prix | 1994 | Programming Instructions |
| Pontiac Grand Prix | 1995 | Programming Instructions |
| Pontiac Grand Prix | 1996 | Programming Instructions |
| Pontiac Grand Prix | 1997 | Programming Instructions |
| Pontiac Grand Prix | 1998 | Programming Instructions |
| Pontiac Grand Prix | 1999 | Programming Instructions |
| Pontiac Grand Prix | 2000 | Programming Instructions |
| Pontiac Grand Prix | 2001 | Programming Instructions |
| Pontiac Grand Prix | 2002 | Programming Instructions |
| Pontiac Grand Prix | 2003 | Programming Instructions |
| Pontiac Grand Prix | 2004 | Programming Instructions |
| Pontiac Grand Prix | 2005 | Programming Instructions |
| Pontiac Grand Prix | 2006 | Programming Instructions |
| Pontiac Grand Prix | 2007 | Programming Instructions |
| Pontiac Grand Prix | 2008 | Programming Instructions |
1994 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
Note: Existing keyless remotes will be erased with this procedure. Existing working remotes will have to reprogrammed also.
- Locate the programming connector wire located in the RH trunk area. You may have to pull back right side trunk trim on trunk wall to locate the single black/white wire.
- The programming connector wire should have one terminal in the plastic connector on end of black/white wire. Ground the terminal in the connector to a nearby bolt or trunk latch. Leave connector wire connected to ground through out procedure.
- System will now lock and unlock doors automatically to indicate programming mode has been activated.
- Press any button on keyless remote. System will respond by locking and unlocking doors one time to indicate successful programming.
- Repeat step 4 for to program any additional keyless remotes including and existing keyless remotes. Do not remove ground wire between programming of keyless remotes.
- Disconnect programming connector wire from ground to exit programming mode.
- Test keyless remote(s).
1994 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
1995 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
Note: Existing keyless remotes will be erased with this procedure. Existing working remotes will have to reprogrammed also.
- Locate the programming connector wire located in the RH trunk area. You may have to pull back right side trunk trim on trunk wall to locate the single black/white wire.
- The programming connector wire should have one terminal in the plastic connector on end of black/white wire. Ground the terminal in the connector to a nearby bolt or trunk latch. Leave connector wire connected to ground through out procedure.
- System will now lock and unlock doors automatically to indicate programming mode has been activated.
- Press any button on keyless remote. System will respond by locking and unlocking doors one time to indicate successful programming.
- Repeat step 4 for to program any additional keyless remotes including and existing keyless remotes. Do not remove ground wire between programming of keyless remotes.
- Disconnect programming connector wire from ground to exit programming mode.
- Test keyless remote(s).
1995 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
1996 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
Note: Existing keyless remotes will be erased with this procedure. Existing working remotes will have to reprogrammed also.
- Locate the programming connector wire located in the RH trunk area. You may have to pull back right side trunk trim on trunk wall to locate the single black/white wire.
- The programming connector wire should have one terminal in the plastic connector on end of black/white wire. Ground the terminal in the connector to a nearby bolt or trunk latch. Leave connector wire connected to ground through out procedure.
- System will now lock and unlock doors automatically to indicate programming mode has been activated.
- Press any button on keyless remote. System will respond by locking and unlocking doors one time to indicate successful programming.
- Repeat step 4 for to program any additional keyless remotes including and existing keyless remotes. Do not remove ground wire between programming of keyless remotes.
- Disconnect programming connector wire from ground to exit programming mode.
- Test keyless remote(s).
1996 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
1997 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.
- Remove the key from the ignition.
- Close all doors.
- Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.
- Insert the key into the ignition, and turn to the ACC position.
- Turn the key to OFF and then back to ACC within 1 second.
- Open and close any vehicle door. A chime will be heard when the system enters into programming mode.
- Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
- Repeat step 7 now for each additional remotes to be programmed including any existing remotes.
- Remove key from ignition.
- Install the "MALL PGM" fuse back into the fuse panel and test remote(s).
1997 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
1998 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.
- Remove the key from the ignition.
- Close all doors.
- Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.
- Insert the key into the ignition, and turn to the ACC position.
- Turn the key to OFF and then back to ACC within 1 second.
- Open and close any vehicle door. A chime will be heard when the system enters into programming mode.
- Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
- Repeat step 7 now for each additional remotes to be programmed including any existing remotes.
- Remove key from ignition.
- Install the "MALL PGM" fuse back into the fuse panel and test remote(s).
1998 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
1999 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.
- Remove the key from the ignition.
- Close all doors.
- Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.
- Insert the key into the ignition, and turn to the ACC position.
- Turn the key to OFF and then back to ACC within 1 second.
- Open and close any vehicle door. A chime will be heard when the system enters into programming mode.
- Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
- Repeat step 7 now for each additional remotes to be programmed including any existing remotes.
- Remove key from ignition.
- Install the "MALL PGM" fuse back into the fuse panel and test remote(s).
1999 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2000 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.
- Remove the key from the ignition.
- Close all doors.
- Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.
- Insert the key into the ignition, and turn to the ACC position.
- Turn the key to OFF and then back to ACC within 1 second.
- Open and close any vehicle door. A chime will be heard when the system enters into programming mode.
- Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
- Repeat step 7 now for each additional remotes to be programmed including any existing remotes.
- Remove key from ignition.
- Install the "MALL PGM" fuse back into the fuse panel and test remote(s).
2000 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2001 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.
- Remove the key from the ignition.
- Close all doors.
- Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.
- Insert the key into the ignition, and turn to the ACC position.
- Turn the key to OFF and then back to ACC within 1 second.
- Open and close any vehicle door. A chime will be heard when the system enters into programming mode.
- Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
- Repeat step 7 now for each additional remotes to be programmed including any existing remotes.
- Remove key from ignition.
- Install the "MALL PGM" fuse back into the fuse panel and test remote(s).
2001 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2002 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.
- Remove the key from the ignition.
- Close all doors.
- Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.
- Insert the key into the ignition, and turn to the ACC position.
- Turn the key to OFF and then back to ACC within 1 second.
- Open and close any vehicle door. A chime will be heard when the system enters into programming mode.
- Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
- Repeat step 7 now for each additional remotes to be programmed including any existing remotes.
- Remove key from ignition.
- Install the "MALL PGM" fuse back into the fuse panel and test remote(s).
2002 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2003 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remote. all previous remotes that were programmed will be erased from memory. The other remotes will not be functional until you program the them again.
- Remove the key from the ignition.
- Close all doors.
- Remove the "MALL PGM" fuse from the fuse panel. Use the legend on the fuse panel or owner's manual to properly locate the "MALL PGM" fuse.
- Insert the key into the ignition, and turn to the ACC position.
- Turn the key to OFF and then back to ACC within 1 second.
- Open and close any vehicle door. A chime will be heard when the system enters into programming mode.
- Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
- Repeat step 7 now for each additional remotes to be programmed including any existing remotes.
- Remove key from ignition.
- Install the "MALL PGM" fuse back into the fuse panel and test remote(s).
2003 Pontiac Grand Prix Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2004 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Pontiac Grand Prix Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Pontiac Montana | 1999 | Programming Instructions |
| Pontiac Montana | 2000 | Programming Instructions |
| Pontiac Montana | 2001 | Programming Instructions |
| Pontiac Montana | 2002 | Programming Instructions |
| Pontiac Montana | 2003 | Programming Instructions |
| Pontiac Montana | 2004 | Programming Instructions |
| Pontiac Montana | 2005 | Programming Instructions |
| Pontiac Montana | 2006 | Programming Instructions |
| Pontiac Montana | 2007 | Programming Instructions |
1999 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2000 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2001 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
For Grand Prix / Chevy Venture / Oldsmobile Silhouette / Pontiac Montana
Obtain all remote transmitters for this vehicle.
- Remove key from ignition.
- Remove the MALL PGM or BCM PRGRM fuse from fuse box (you only need to remove one fuse on this step. In some vehicles it’s called MALL PGM and in others it’s BCM PRGRM).
- Close all doors.
- Turn ignition switch to ACC. (ACC is turning the key back toward you).
- Within 1 second turn the ignition to OFF then back to ACC. (OFF is the position where you can remove your key)
- Open then close the driver’s door.
- An acoustic sound will be heard after closing the door indicating the vehicle is in programming mode.
- Hold the LOCK and UNLOCK buttons on the remote for about 15 seconds until two chimes are heard.
- Repeat step 8 for any additional remotes including working ones.
- Remove key from ignition and replace MALL PGM or BCM PRGRM fuse.
- Test all remotes.
2001 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2002 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
For Grand Prix / Chevy Venture / Oldsmobile Silhouette / Pontiac Montana
Obtain all remote transmitters for this vehicle.
- Remove key from ignition.
- Remove the MALL PGM or BCM PRGRM fuse from fuse box (you only need to remove one fuse on this step. In some vehicles it’s called MALL PGM and in others it’s BCM PRGRM).
- Close all doors.
- Turn ignition switch to ACC. (ACC is turning the key back toward you).
- Within 1 second turn the ignition to OFF then back to ACC. (OFF is the position where you can remove your key)
- Open then close the driver’s door.
- An acoustic sound will be heard after closing the door indicating the vehicle is in programming mode.
- Hold the LOCK and UNLOCK buttons on the remote for about 15 seconds until two chimes are heard.
- Repeat step 8 for any additional remotes including working ones.
- Remove key from ignition and replace MALL PGM or BCM PRGRM fuse.
- Test all remotes.
2002 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2003 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
For Grand Prix / Chevy Venture / Oldsmobile Silhouette / Pontiac Montana
Obtain all remote transmitters for this vehicle.
- Remove key from ignition.
- Remove the MALL PGM or BCM PRGRM fuse from fuse box (you only need to remove one fuse on this step. In some vehicles it’s called MALL PGM and in others it’s BCM PRGRM).
- Close all doors.
- Turn ignition switch to ACC. (ACC is turning the key back toward you).
- Within 1 second turn the ignition to OFF then back to ACC. (OFF is the position where you can remove your key)
- Open then close the driver’s door.
- An acoustic sound will be heard after closing the door indicating the vehicle is in programming mode.
- Hold the LOCK and UNLOCK buttons on the remote for about 15 seconds until two chimes are heard.
- Repeat step 8 for any additional remotes including working ones.
- Remove key from ignition and replace MALL PGM or BCM PRGRM fuse.
- Test all remotes.
2003 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2004 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
For Grand Prix / Chevy Venture / Oldsmobile Silhouette / Pontiac Montana
Obtain all remote transmitters for this vehicle.
- Remove key from ignition.
- Remove the MALL PGM or BCM PRGRM fuse from fuse box (you only need to remove one fuse on this step. In some vehicles it’s called MALL PGM and in others it’s BCM PRGRM).
- Close all doors.
- Turn ignition switch to ACC. (ACC is turning the key back toward you).
- Within 1 second turn the ignition to OFF then back to ACC. (OFF is the position where you can remove your key)
- Open then close the driver’s door.
- An acoustic sound will be heard after closing the door indicating the vehicle is in programming mode.
- Hold the LOCK and UNLOCK buttons on the remote for about 15 seconds until two chimes are heard.
- Repeat step 8 for any additional remotes including working ones.
- Remove key from ignition and replace MALL PGM or BCM PRGRM fuse.
- Test all remotes.
2004 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2005 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
For Grand Prix / Chevy Venture / Oldsmobile Silhouette / Pontiac Montana
Obtain all remote transmitters for this vehicle.
- Remove key from ignition.
- Remove the MALL PGM or BCM PRGRM fuse from fuse box (you only need to remove one fuse on this step. In some vehicles it’s called MALL PGM and in others it’s BCM PRGRM).
- Close all doors.
- Turn ignition switch to ACC. (ACC is turning the key back toward you).
- Within 1 second turn the ignition to OFF then back to ACC. (OFF is the position where you can remove your key)
- Open then close the driver’s door.
- An acoustic sound will be heard after closing the door indicating the vehicle is in programming mode.
- Hold the LOCK and UNLOCK buttons on the remote for about 15 seconds until two chimes are heard.
- Repeat step 8 for any additional remotes including working ones.
- Remove key from ignition and replace MALL PGM or BCM PRGRM fuse.
- Test all remotes.
2005 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2006 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2006 Pontiac Montana Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2007 Pontiac Montana Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Pontiac Pursuit | 2006 | Programming Instructions |
| Pontiac Pursuit | 2007 | Programming Instructions |
| Pontiac Pursuit | 2008 | Programming Instructions |
| Pontiac Pursuit | 2009 | Programming Instructions |
| Pontiac Pursuit | 2010 | Programming Instructions |
| Pontiac Pursuit | 2011 | Programming Instructions |
2006 Pontiac Pursuit Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2006 Pontiac Pursuit Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2007 Pontiac Pursuit Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Pontiac Pursuit Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Pontiac Pursuit Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2008 Pontiac Pursuit Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Pontiac Pursuit Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2009 Pontiac Pursuit Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Pontiac Pursuit Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Pontiac Pursuit Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2011 Pontiac Pursuit Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2011 Pontiac Pursuit Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Pontiac Solstice | 2006 | Programming Instructions |
| Pontiac Solstice | 2007 | Programming Instructions |
| Pontiac Solstice | 2008 | Programming Instructions |
| Pontiac Solstice | 2009 | Programming Instructions |
| Pontiac Solstice | 2010 | Programming Instructions |
2006 Pontiac Solstice Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2006 Pontiac Solstice Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2007 Pontiac Solstice Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2007 Pontiac Solstice Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Pontiac Solstice Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2008 Pontiac Solstice Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Pontiac Solstice Keyless Entry Remote Fob Programming Instructions
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.
2009 Pontiac Solstice Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Pontiac Solstice Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Pontiac Solstice Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Pontiac Torrent | 2006 | Programming Instructions |
| Pontiac Torrent | 2007 | Programming Instructions |
| Pontiac Torrent | 2008 | Programming Instructions |
| Pontiac Torrent | 2009 | Programming Instructions |
| Pontiac Torrent | 2010 | Programming Instructions |
2006 Pontiac Torrent Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2007 Pontiac Torrent Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2007 Pontiac Torrent Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2008 Pontiac Torrent Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2008 Pontiac Torrent Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2009 Pontiac Torrent Keyless Entry Remote Fob Programming Instructions
There are 2 possible procedures for this GM vehicle
NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only
1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.
- Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
- Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
- Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.
- Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
- Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
- Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
- Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
- Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
- To exit programming mode turn ignition OFF, remove key and test all remotes.
2009 Pontiac Torrent Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
2010 Pontiac Torrent Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Pontiac Torrent Key Programming Instructions
- Insert the original, already programmed key in the ignition and start the engine.
- After the engine has started, turn the key to off and remove the key.
- Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
- The security light will turn off once the key has been programmed. It may not be apparent if the security lightwent on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
- Repeat steps 1 through 5 if additional keys are to be programmed.
| Model | Year | |
|---|---|---|
| Pontiac Vibe | 2009 | Programming Instructions |
| Pontiac Vibe | 2010 | Programming Instructions |
2009 Pontiac Vibe Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.
Insert the key into the ignition (Do NOT Turn it) and Pull key out. - Within 40 seconds, Close then open the drivers door.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2009 Pontiac Vibe Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Pontiac Vibe Keyless Entry Remote Fob Programming Instructions
Have all transmitters for the vehicle at hand
- With the key out of the ignition, unlock and open drivers door (all other doors must be closed)
- Within 5 seconds,
Insert the key into the ignition (Do NOT Turn it) and Pull key out.
Insert the key into the ignition (Do NOT Turn it) and Pull key out. - Within 40 seconds, Close then open the drivers door.
- Close then open the drivers door.
- Within 40 seconds. Close then open the drivers door.
- Insert the key into the ignition (Do NOT Turn it) and Pull key out.
- Close then open the drivers door.
- Insert the key into ignition and leave it in the ignition.
- Close the drivers door. Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the door locks do not cycle at this point or try the alternate procedure listed below.
- Within 40 second, A. Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
- Remove the key from the ignition.
- B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.
- Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.
- (If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted) Repeat steps A and B in step 6 for each new remote.
- Open drivers door.
Alternate programming procedure: Have all remotes for the vehicle ready. Toyota Avalon vehicles use step 10a, all other vehicles use 10b.
- Make sure all doors are closed
- Open Driver’s door
- Insert key into ignition, then remove it
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Close and re-open driver’s door
- Press LOCK and UNLOCK on the vehicle door lock switch at 1 second intervals 5 times.
- Insert key into ignition switch
- Turn the ignition to ON then back to OFF (Do NOT Start or crank engine).
- Remove Key from ignition
- Door locks should cycle to confirm entry into programming mode a. AVALON – Press LOCK on remote for a minimum of 1 second
- b. ALL OTHER VEHICLES – Press and hold LOCK & UNLOCK together for 1.5 seconds; then press and hold LOCK until the locks cycle
- Locks should cycle once to confirm programming. If they cycle twice, the programming failed
- Repeat button procedure to program remaining remotes
- Close driver’s door. Test remotes.
2010 Pontiac Vibe Key Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
