Nissan Keyless Entry Remote Fob Programming Instructions

2002 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2002 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2003 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2003 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2004 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2004 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2005 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2005 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2006 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2006 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2007 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2007 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2008 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2008 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2009 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2009 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2010 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2010 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2011 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2011 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2012 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2012 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2013 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2013 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2014 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2014 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2015 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2015 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2016 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)

Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.

1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals). You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all remotes.

2016 Nissan Frontier Key Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2020 Nissan Frontier Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.