Mazda Keyless Entry Remote Fob Programming Instructions

2011 Mazda 2 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2011 Mazda 2 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2012 Mazda 2 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2012 Mazda 2 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2013 Mazda 2 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2013 Mazda 2 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2014 Mazda 2 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2014 Mazda 2 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2015 Mazda 2 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2015 Mazda 2 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2004 Mazda 3 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2004 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2005 Mazda 3 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2005 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2006 Mazda 3 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2006 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2007 Mazda 3 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2007 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2008 Mazda 3 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2008 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2009 Mazda 3 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2009 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2010 Mazda 3 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2010 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2011 Mazda 3 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2011 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2012 Mazda 3 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2012 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2013 Mazda 3 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2013 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2014 Mazda 3 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2014 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2015 Mazda 3 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2015 Mazda 3 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2006 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2006 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2007 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2007 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2008 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2008 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2009 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2009 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2010 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2010 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2011 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2011 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2012 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2012 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2013 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2013 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2014 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2014 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2015 Mazda 5 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2015 Mazda 5 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2003 Mazda 6 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2003 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2004 Mazda 6 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2004 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2005 Mazda 6 Keyless Entry Remote Fob Programming Instructions

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2005 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2006 Mazda 6 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2006 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2007 Mazda 6 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2007 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2008 Mazda 6 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2008 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2009 Mazda 6 Keyless Entry Remote Fob Programming Instructions

For vehicles without Smart Entry System

1. Get in vehicle and close all doors, then open the drivers door and leave it open.
2. Within 24 seconds you must insert key into the ignition and cycle the ignition switch to ON and then OFF three times and leave the key in the ignition. Then close and open the drivers door three times.
3. When done properly the doors will automatically lock and then unlock. Now the vehicle is in programming mode. If locks do not cycle you must start the procedure over.
4. Push the unlock button twice on the first remote to be programmed. The door locks will cycle automatically to indicate successful programming. If there is only one remote to be programmed to the vehicle you must push any button twice again on the same remote, wait for locks to cycle, then push any button twice one more time on the same remote.
If there are two remotes to be programmed then press any button on the second remote twice, wait for locks to cycle, then push any button twice again on the second remote. To program three remotes to this vehicle you must press button twice on second remote, wait for locks to cycle, then press any button twice on the third remote.
5. Programming is now complete. Close the door and test remotes to ensure proper programming.

2009 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2010 Mazda 6 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2010 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2011 Mazda 6 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2011 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2012 Mazda 6 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2012 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2013 Mazda 6 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2013 Mazda 6 Key Programming Instructions

You must have 2 original Ford keys that start your engine to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! Your New third (unprogrammed) key must also be cut prior to performing this procedure.

Please Note: If one of your keys is a cloned key from a hardware store this procedure will NOT work. This procedure requires original programmed keys.

1. Insert an existing (working) key into the ignition cylinder.
2. Turn the ignition cylinder ON (just shy of starting the car Without cranking the engine) and back to OFF. Ignition should stay in ON position for at least one second.
3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition must be on for at least one second but no more than ten seconds. Remove key.
4. Insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least one second and turn back to OFF.
5. The security light will light up for THREE seconds to indicate the new key has been successfully programmed.

For those who do not have 2 original keys: These keys can NOT be programmed at hardware stores like Ace, Lowes, Walmart, & Home Depot. They must be programmed by an automotive locksmith or dealership.

2014 Mazda 6 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.