Jeep Keyless Entry Remote Fob Programming Instructions
Keyless Entry Remote Fob Programming Instructions Available for the following Jeep models.
Click below to select your model.
| Model | Year | |
|---|---|---|
| Jeep Cherokee | 1998 | Programming Instructions |
| Jeep Cherokee | 1999 | Programming Instructions |
| Jeep Cherokee | 2000 | Programming Instructions |
| Jeep Cherokee | 2001 | Programming Instructions |
| Jeep Cherokee | 2014 | Programming Instructions |
| Jeep Cherokee | 2015 | Programming Instructions |
1998 Jeep Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Jeep Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
1999 Jeep Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Jeep Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2000 Jeep Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Jeep Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2001 Jeep Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Jeep Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2014 Jeep Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Jeep Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Jeep Commander | 2006 | Programming Instructions |
| Jeep Commander | 2007 | Programming Instructions |
| Jeep Commander | 2008 | Programming Instructions |
| Jeep Commander | 2009 | Programming Instructions |
| Jeep Commander | 2010 | Programming Instructions |
2006 Jeep Commander Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2007 Jeep Commander Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2008 Jeep Commander Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2009 Jeep Commander Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2010 Jeep Commander Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Jeep Commander Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
| Model | Year | |
|---|---|---|
| Jeep Compass | 2007 | Programming Instructions |
| Jeep Compass | 2008 | Programming Instructions |
| Jeep Compass | 2009 | Programming Instructions |
| Jeep Compass | 2010 | Programming Instructions |
| Jeep Compass | 2011 | Programming Instructions |
| Jeep Compass | 2012 | Programming Instructions |
| Jeep Compass | 2013 | Programming Instructions |
| Jeep Compass | 2014 | Programming Instructions |
| Jeep Compass | 2015 | Programming Instructions |
| Jeep Compass | 2016 | Programming Instructions |
| Jeep Compass | 2017 | Programming Instructions |
| Jeep Compass | 2018 | Programming Instructions |
| Jeep Compass | 2019 | Programming Instructions |
| Jeep Compass | 2020 | Programming Instructions |
| Jeep Compass | 2021 | Programming Instructions |
2007 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2008 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2009 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2010 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2011 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2012 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Jeep/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2013 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2014 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2015 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2016 Jeep Compass Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2017 Jeep Compass Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2018 Jeep Compass Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2019 Jeep Compass Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2020 Jeep Compass Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2021 Jeep Compass Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Jeep Grand Cherokee | 1998 | Programming Instructions |
| Jeep Grand Cherokee | 1999 | Programming Instructions |
| Jeep Grand Cherokee | 2000 | Programming Instructions |
| Jeep Grand Cherokee | 2001 | Programming Instructions |
| Jeep Grand Cherokee | 2002 | Programming Instructions |
| Jeep Grand Cherokee | 2003 | Programming Instructions |
| Jeep Grand Cherokee | 2004 | Programming Instructions |
| Jeep Grand Cherokee | 2005 | Programming Instructions |
| Jeep Grand Cherokee | 2006 | Programming Instructions |
| Jeep Grand Cherokee | 2007 | Programming Instructions |
| Jeep Grand Cherokee | 2008 | Programming Instructions |
| Jeep Grand Cherokee | 2009 | Programming Instructions |
| Jeep Grand Cherokee | 2010 | Programming Instructions |
| Jeep Grand Cherokee | 2011 | Programming Instructions |
| Jeep Grand Cherokee | 2012 | Programming Instructions |
| Jeep Grand Cherokee | 2013 | Programming Instructions |
| Jeep Grand Cherokee | 2014 | Programming Instructions |
| Jeep Grand Cherokee | 2015 | Programming Instructions |
| Jeep Grand Cherokee | 2016 | Programming Instructions |
| Jeep Grand Cherokee | 2017 | Programming Instructions |
| Jeep Grand Cherokee | 2018 | Programming Instructions |
| Jeep Grand Cherokee | 2019 | Programming Instructions |
| Jeep Grand Cherokee | 2020 | Programming Instructions |
1998 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Jeep Grand Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
1999 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Jeep Grand Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2000 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Jeep Grand Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2001 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Jeep Grand Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2002 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Jeep Grand Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2003 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2004 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Jeep Grand Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2005 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2006 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2007 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2008 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2009 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2010 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2010 Jeep Grand Cherokee Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2011 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2013 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2014 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2015 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2017 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2018 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2019 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2020 Jeep Grand Cherokee Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Jeep Liberty | 2002 | Programming Instructions |
| Jeep Liberty | 2003 | Programming Instructions |
| Jeep Liberty | 2004 | Programming Instructions |
| Jeep Liberty | 2005 | Programming Instructions |
| Jeep Liberty | 2006 | Programming Instructions |
| Jeep Liberty | 2007 | Programming Instructions |
| Jeep Liberty | 2008 | Programming Instructions |
| Jeep Liberty | 2009 | Programming Instructions |
| Jeep Liberty | 2010 | Programming Instructions |
| Jeep Liberty | 2011 | Programming Instructions |
| Jeep Liberty | 2012 | Programming Instructions |
2002 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2
Programming procedure #1.
Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
- Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
- While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
- Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
- Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
- Programming is now complete. Turn ignition off and test remotes to ensure proper programming.
Programming Procedure #2
Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
- Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
- While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
- Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
- Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
- Programming is now complete. Turn ignition off and test remotes to ensure proper programming.
2002 Jeep Liberty Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2003 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2
Programming procedure #1.
Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
- Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
- While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
- Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
- Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
- Programming is now complete. Turn ignition off and test remotes to ensure proper programming.
Programming Procedure #2
Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
- Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
- While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
- Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
- Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
- Programming is now complete. Turn ignition off and test remotes to ensure proper programming.
2003 Jeep Liberty Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2004 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2
Programming procedure #1.
Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
- Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
- While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
- Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
- Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
- Programming is now complete. Turn ignition off and test remotes to ensure proper programming.
Programming Procedure #2
Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
- Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
- Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
- While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
- Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
- Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
- Programming is now complete. Turn ignition off and test remotes to ensure proper programming.
2004 Jeep Liberty Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2005 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2006 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2007 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2008 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2009 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2010 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2011 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2012 Jeep Liberty Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
| Model | Year | |
|---|---|---|
| Jeep Patriot | 2007 | Programming Instructions |
| Jeep Patriot | 2008 | Programming Instructions |
| Jeep Patriot | 2009 | Programming Instructions |
| Jeep Patriot | 2010 | Programming Instructions |
| Jeep Patriot | 2011 | Programming Instructions |
| Jeep Patriot | 2012 | Programming Instructions |
| Jeep Patriot | 2013 | Programming Instructions |
| Jeep Patriot | 2014 | Programming Instructions |
| Jeep Patriot | 2015 | Programming Instructions |
| Jeep Patriot | 2016 | Programming Instructions |
2007 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2008 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2009 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2010 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2011 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2012 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2013 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2014 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2015 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2016 Jeep Patriot Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
| Model | Year | |
|---|---|---|
| Jeep Renegade | 2015 | Programming Instructions |
| Jeep Renegade | 2016 | Programming Instructions |
| Jeep Renegade | 2017 | Programming Instructions |
| Jeep Renegade | 2018 | Programming Instructions |
| Jeep Renegade | 2019 | Programming Instructions |
| Jeep Renegade | 2020 | Programming Instructions |
| Jeep Renegade | 2021 | Programming Instructions |
2015 Jeep Renegade Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2016 Jeep Renegade Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2017 Jeep Renegade Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2018 Jeep Renegade Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2019 Jeep Renegade Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2020 Jeep Renegade Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2021 Jeep Renegade Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1998 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
1999 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
1999 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2000 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2000 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2001 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2001 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2002 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2002 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2003 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2003 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2004 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2004 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2005 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.
Find A Locksmith
2005 Jeep Wrangler Key Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2006 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2007 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2008 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2009 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2010 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2011 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2012 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure
*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***
***If ignition recall was performed on your vehicle, the DIY programming won’t be available***
ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2013 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2014 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2015 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
2016 Jeep Wrangler Keyless Entry Remote Fob Programming Instructions
Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure.
Your new keys must be cut prior to performing this procedure.
Remote portion and immobilizer are programmed during the same programming procedure.
Please note: this programming procedure WILL NOT WORK if your vehicle has PUSH BUTTON ignition.
- Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
- Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
- Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
- For each additional key you must repeat these steps starting with step number 1.
