Dodge Keyless Entry Remote Fob Programming Instructions

1999 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2000 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2001 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2002 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2002 Dodge Ram 1500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2003 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2003 Dodge Ram 1500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2004 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2004 Dodge Ram 1500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2005 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2005 Dodge Ram 1500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2006 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

Transponder Vehicles:

Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.

NON-Transponder Vehicles:

This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.

Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Using a programmed key/remote transmitter perform the following:

   • Press and hold UNLOCK button.
   • After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
   • Ensure acoustic signal is emitted indicating programming mode active.
   • Release both buttons.

4. Within 60 seconds carry out the following procedure for each remaining key/remote transmitter:

   • On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
   • Ensure acoustic signal is emitted
   • Within 4 seconds press and release the UNLOCK button.
   • Ensure acoustic signal is emitted
5. Repeat step 3 now for each remaining key/remote transmitters including working remotes.
6. Switch ignition to OFF position or wait 60 seconds to exit programming mode.
7. Programming is now complete. Test all remotes to ensure proper programming.

Please note: a maximum 6 key remote transmitters can be programmed

Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.

2006 Dodge Ram 1500 Key Programming Instructions

Transponder Vehicles:

You must have two working programmed or original keys to use this procedure.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
4. For each additional key you must repeat these steps starting with step number 1.

NON-Transponder Vehicles:

Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.

2007 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

Transponder Vehicles:

Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.

NON-Transponder Vehicles:

This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.

Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Using a programmed key/remote transmitter perform the following:

   • Press and hold UNLOCK button.
   • After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
   • Ensure acoustic signal is emitted indicating programming mode active.
   • Release both buttons.

4. Within 60 seconds carry out the following procedure for each remaining key/remote transmitter:

   • On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
   • Ensure acoustic signal is emitted
   • Within 4 seconds press and release the UNLOCK button.
   • Ensure acoustic signal is emitted
5. Repeat step 3 now for each remaining key/remote transmitters including working remotes.
6. Switch ignition to OFF position or wait 60 seconds to exit programming mode.
7. Programming is now complete. Test all remotes to ensure proper programming.

Please note: a maximum 6 key remote transmitters can be programmed

Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.

2007 Dodge Ram 1500 Key Programming Instructions

Transponder Vehicles:

You must have two working programmed or original keys to use this procedure.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
4. For each additional key you must repeat these steps starting with step number 1.

NON-Transponder Vehicles:

Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.

2008 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2008 Dodge Ram 1500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2009 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2010 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2011 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2012 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2013 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2014 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2015 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2016 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2017 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2018 Dodge Ram 1500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

1999 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2000 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2001 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2002 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2002 Dodge Ram 2500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2003 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2003 Dodge Ram 2500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2004 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2004 Dodge Ram 2500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2005 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2005 Dodge Ram 2500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2006 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

Transponder Vehicles:

Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.

NON-Transponder Vehicles:

This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.

Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Using a programmed key/remote transmitter perform the following:

   • Press and hold UNLOCK button.
   • After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
   • Ensure acoustic signal is emitted indicating programming mode active.
   • Release both buttons.

4. Within 60 seconds carry out the following procedure for each remaining key/remote transmitter:

   • On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
   • Ensure acoustic signal is emitted
   • Within 4 seconds press and release the UNLOCK button.
   • Ensure acoustic signal is emitted
5. Repeat step 3 now for each remaining key/remote transmitters including working remotes.
6. Switch ignition to OFF position or wait 60 seconds to exit programming mode.
7. Programming is now complete. Test all remotes to ensure proper programming.

Please note: a maximum 6 key remote transmitters can be programmed

Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.

2006 Dodge Ram 2500 Key Programming Instructions

Transponder Vehicles:

You must have two working programmed or original keys to use this procedure.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
4. For each additional key you must repeat these steps starting with step number 1.

NON-Transponder Vehicles:

Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.

2007 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

Transponder Vehicles:

Transmitter for the remote key combo is programmed during the Key Programming procedure. Click on the Key Programming for your vehicle to access programming instructions.

NON-Transponder Vehicles:

This programming procedure requires you to already have at least 1 working original remote transmitter. (All buttons must be functional). If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership.

Obtain all remote transmitters for this vehicle. Any existing keys/remote transmitters not used during programming will become inoperative so make sure to reprogram them during procedure describe below. Sit in vehicle with all doors closed and the driver’s seat-belt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).

2. Using a programmed key/remote transmitter perform the following:

   • Press and hold UNLOCK button.
   • After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.
   • Ensure acoustic signal is emitted indicating programming mode active.
   • Release both buttons.

4. Within 60 seconds carry out the following procedure for each remaining key/remote transmitter:

   • On the unprogrammed remote, press both the LOCK and UNLOCK button at the same time for 2 seconds then release both buttons.
   • Ensure acoustic signal is emitted
   • Within 4 seconds press and release the UNLOCK button.
   • Ensure acoustic signal is emitted
5. Repeat step 3 now for each remaining key/remote transmitters including working remotes.
6. Switch ignition to OFF position or wait 60 seconds to exit programming mode.
7. Programming is now complete. Test all remotes to ensure proper programming.

Please note: a maximum 6 key remote transmitters can be programmed

Please note: if the vehicle goes into programming mode, but there is no acoustic signal from the new remote, then repeat this procedure again starting from 1st Step.

2007 Dodge Ram 2500 Key Programming Instructions

Transponder Vehicles:

You must have two working programmed or original keys to use this procedure.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turn ignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming is completed.
4. For each additional key you must repeat these steps starting with step number 1.

NON-Transponder Vehicles:

Programming is not required, just get the key blade cut at your local locksmith/dealer and it will start the engine.

2008 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2008 Dodge Ram 2500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2009 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2010 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2011 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2012 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2013 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2014 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2015 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2016 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2017 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2018 Dodge Ram 2500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

1999 Dodge Ram 3500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2000 Dodge Ram 3500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2001 Dodge Ram 3500 Keyless Entry Remote Fob Programming Instructions

DIY key programmer procedure is not available for this vehicle. This vehicle requires a key diagnostic equipment such as Autel IM608 Pro, Smart Pro, AutoProPad or any other transponder key programmer to be connected to the vehicle to program the remote key fob. You will need to contact a local auto locksmith. Please follow the link below to find a locksmith near you.

2002 Dodge Ram 3500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2002 Dodge Ram 3500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2003 Dodge Ram 3500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2003 Dodge Ram 3500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2004 Dodge Ram 3500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
5. Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. Repeat step 5. for all additional remotes including working remotes.
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

2004 Dodge Ram 3500 Key Programming Instructions

Have all keys for the Dodge/Chrysler/Jeep ready – You must have two working programmed or original keys to use this procedure

*** 2010+ VEHICLES MUST BE PROGRAMMED BY AN AUTOMOTIVE LOCKSMITH OR DEALER ***

***If ignition recall was performed on your vehicle, the DIY programming won’t be available***

ATTENTION DODGE RAM OWNERS: Some 2009 and up DODGE RAM’S may require dealer programming. If you have a 2009 DODGE RAM, please contact your local dealership to see if your vehicle requires dealer programming.

1. Insert first programmed key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.
2. Within 15 seconds of removing first key insert second programmed key into ignition and turn ignition switch to ON. Waitapproximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.
3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 secondsyou should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.
4. For each additional key you must repeat these steps starting with step number 1.

2005 Dodge Ram 3500 Keyless Entry Remote Fob Programming Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have anyremote transmitters you must get this new one programmed by a qualified locksmith or dealership.Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. Ifthat does not work, use procedure 2

Programming procedure #1.

Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

1. Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine).
2. Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds.
3. While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. A chime should sound within three seconds to indicate the vehicle has entered programming mode.
4. Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing first chime in step 3.
5. Within 30 seconds – Press the Unlock button on the next remote. -Repeat step 5. for all additional remotes including working remotes
6. Programming is now complete. Turn ignition off and test remotes to ensure proper programming.

Programming Procedure #2