Chevrolet Keyless Remote and Key Programming Page 1

Model	Year
Chevrolet Astro	1999	Programming Instructions
Chevrolet Astro	2000	Programming Instructions
Chevrolet Astro	2001	Programming Instructions
Chevrolet Astro	2002	Programming Instructions
Chevrolet Astro	2003	Programming Instructions
Chevrolet Astro	2004	Programming Instructions
Chevrolet Astro	2005	Programming Instructions
Chevrolet Astro	2006	Programming Instructions

Model	Year
Chevrolet Avalanche	2007	Programming Instructions
Chevrolet Avalanche	2008	Programming Instructions
Chevrolet Avalanche	2009	Programming Instructions
Chevrolet Avalanche	2010	Programming Instructions
Chevrolet Avalanche	2011	Programming Instructions
Chevrolet Avalanche	2012	Programming Instructions
Chevrolet Avalanche	2013	Programming Instructions

2007 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2007 Chevrolet Avalanche Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2008 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2008 Chevrolet Avalanche Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2009 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2009 Chevrolet Avalanche Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2010 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2010 Chevrolet Avalanche Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

Model	Year
Chevrolet Avalanche 1500	2002	Programming Instructions
Chevrolet Avalanche 1500	2003	Programming Instructions
Chevrolet Avalanche 1500	2004	Programming Instructions
Chevrolet Avalanche 1500	2005	Programming Instructions
Chevrolet Avalanche 1500	2006	Programming Instructions

Model	Year
Chevrolet Avalanche 2500	2003	Programming Instructions
Chevrolet Avalanche 2500	2004	Programming Instructions
Chevrolet Avalanche 2500	2005	Programming Instructions
Chevrolet Avalanche 2500	2006	Programming Instructions

Model	Year
Chevrolet Blazer	1999	Programming Instructions
Chevrolet Blazer	2000	Programming Instructions
Chevrolet Blazer	2001	Programming Instructions
Chevrolet Blazer	2002	Programming Instructions
Chevrolet Blazer	2003	Programming Instructions
Chevrolet Blazer	2004	Programming Instructions
Chevrolet Blazer	2005	Programming Instructions

Model	Year
Chevrolet Camaro	2010	Programming Instructions
Chevrolet Camaro	2011	Programming Instructions
Chevrolet Camaro	2012	Programming Instructions
Chevrolet Camaro	2013	Programming Instructions
Chevrolet Camaro	2014	Programming Instructions
Chevrolet Camaro	2015	Programming Instructions
Chevrolet Camaro	2016	Programming Instructions

Model	Year
Chevrolet Captiva Sport	2011	Programming Instructions
Chevrolet Captiva Sport	2012	Programming Instructions
Chevrolet Captiva Sport	2013	Programming Instructions
Chevrolet Captiva Sport	2014	Programming Instructions
Chevrolet Captiva Sport	2015	Programming Instructions

Model	Year
Chevrolet Cavalier	2000	Programming Instructions
Chevrolet Cavalier	2001	Programming Instructions
Chevrolet Cavalier	2002	Programming Instructions
Chevrolet Cavalier	2003	Programming Instructions
Chevrolet Cavalier	2004	Programming Instructions
Chevrolet Cavalier	2005	Programming Instructions

Model	Year
Chevrolet Cobalt	2005	Programming Instructions
Chevrolet Cobalt	2006	Programming Instructions
Chevrolet Cobalt	2007	Programming Instructions
Chevrolet Cobalt	2008	Programming Instructions
Chevrolet Cobalt	2009	Programming Instructions
Chevrolet Cobalt	2010	Programming Instructions

Model	Year
Chevrolet Colorado	2004	Programming Instructions
Chevrolet Colorado	2005	Programming Instructions
Chevrolet Colorado	2006	Programming Instructions
Chevrolet Colorado	2007	Programming Instructions
Chevrolet Colorado	2008	Programming Instructions
Chevrolet Colorado	2009	Programming Instructions
Chevrolet Colorado	2010	Programming Instructions
Chevrolet Colorado	2011	Programming Instructions
Chevrolet Colorado	2012	Programming Instructions

Model	Year
Chevrolet Corvette	2001	Programming Instructions
Chevrolet Corvette	2002	Programming Instructions
Chevrolet Corvette	2003	Programming Instructions
Chevrolet Corvette	2004	Programming Instructions

Model	Year
Chevrolet Cruze	2011	Programming Instructions
Chevrolet Cruze	2012	Programming Instructions
Chevrolet Cruze	2013	Programming Instructions
Chevrolet Cruze	2014	Programming Instructions
Chevrolet Cruze	2015	Programming Instructions
Chevrolet Cruze	2016	Programming Instructions
Chevrolet Cruze	2017	Programming Instructions
Chevrolet Cruze	2018	Programming Instructions
Chevrolet Cruze	2019	Programming Instructions

2011 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be-off and all of the transmitters, both currently recognized and new, must be with you. The key blade needs to be cut prior to performing this programming procedure.

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

lf there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you. The key blade needs to be cut prior to performing this programming procedure. It is recommended that the vehicle be connected to a power source via jumper cables during this procedure as the vehicle’s battery voltage will drop during the procedure.

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2012 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2013 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2014 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2015 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2016 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2017 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Before you start programming, make sure that the vehicle engine is off and all smart keys, both currently working and new, are with you. Please read and understand the programming procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

If you only have 1 working smart key or none, please follow the steps below. This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada. Before you start programming, make sure that the vehicle is off and all smart keys, both currently working and new, are with you. Please read and understand the entire procedure before you begin. You can also find instructions specific to your vehicle in the vehicle owner’s manual. Up to 8 smart keys can be programmed to a vehicle.

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

2018 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

2019 Chevrolet Cruze Keyless Entry Remote Fob Programming Instructions

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

Model	Year
Chevrolet Equinox	2005	Programming Instructions
Chevrolet Equinox	2006	Programming Instructions
Chevrolet Equinox	2007	Programming Instructions
Chevrolet Equinox	2008	Programming Instructions
Chevrolet Equinox	2009	Programming Instructions
Chevrolet Equinox	2010	Programming Instructions
Chevrolet Equinox	2011	Programming Instructions
Chevrolet Equinox	2012	Programming Instructions
Chevrolet Equinox	2013	Programming Instructions
Chevrolet Equinox	2014	Programming Instructions
Chevrolet Equinox	2015	Programming Instructions
Chevrolet Equinox	2016	Programming Instructions
Chevrolet Equinox	2017	Programming Instructions
Chevrolet Equinox	2018	Programming Instructions
Chevrolet Equinox	2019	Programming Instructions
Chevrolet Equinox	2020	Programming Instructions
Chevrolet Equinox	2021	Programming Instructions

2007 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2007 Chevrolet Equinox Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2008 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2008 Chevrolet Equinox Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2009 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2009 Chevrolet Equinox Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2013 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2015 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2015 Chevrolet Equinox Key Programming

These instructions work only for non-PEPS keys. They will not work if your vehicle has passive entry.

Also, these programming instructions will not work if you have Canadian vehicle.

This procedure adds keys only. Previously programmed keys will not be erased.

This procedure will program both remote and key portions.

Your new unprogrammed key must be cut before performing these steps

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2016 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

2017 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Programming with Two Working Keys:

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

Programming without Two Working Keys

This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada.

Insert the new vehicle key into the ignition.
Turn to ON/RUN. The security light will come on.
Wait 10 minutes until the security light turns off.
Turn the ignition to LOCK/OFF.
Repeat Steps 2–4 two more times. After the third time, turn to ON/RUN; the new key is now programmed and all previously programmed keys will no longer work with the vehicle.
To program the second key, turn to OFF and insert the second key to be learned and rotate to ON/RUN.

If you have more keys to program please follow Programming with Two Working Keys procedure (see above).

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2018 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Programming with Two Working Keys:

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

Programming without Two Working Keys

This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada.

Insert the new vehicle key into the ignition.
Turn to ON/RUN. The security light will come on.
Wait 10 minutes until the security light turns off.
Turn the ignition to LOCK/OFF.
Repeat Steps 2–4 two more times. After the third time, turn to ON/RUN; the new key is now programmed and all previously programmed keys will no longer work with the vehicle.
To program the second key, turn to OFF and insert the second key to be learned and rotate to ON/RUN.

If you have more keys to program please follow Programming with Two Working Keys procedure (see above).

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

2019 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Programming with Two Working Keys:

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

Programming without Two Working Keys

This procedure will take approximately 30 minutes to complete. DIY programming is not available in Canada.

Insert the new vehicle key into the ignition.
Turn to ON/RUN. The security light will come on.
Wait 10 minutes until the security light turns off.
Turn the ignition to LOCK/OFF.
Repeat Steps 2–4 two more times. After the third time, turn to ON/RUN; the new key is now programmed and all previously programmed keys will no longer work with the vehicle.
To program the second key, turn to OFF and insert the second key to be learned and rotate to ON/RUN.

If you have more keys to program please follow Programming with Two Working Keys procedure (see above).

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

2020 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

2021 Chevrolet Equinox Keyless Entry Remote Fob Programming Instructions

DIY PROGRAMMING INSTRUCTIONS FOR GM VEHICLES WITH PUSH-BUTTON IGNITION THAT USE SMART KEYS FEATURED BELOW:

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

A. Programming with Two Working Smart Keys

Remove the emergency key blade from one of the working smart keys.
Place the two working smart keys in the cupholder.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock) The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press the ENGINE START/STOP button. When the new smart key is recognized by the vehicle the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the remote.
To program an additional smart key, repeat Steps 4-6.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

B. Programming without Two Working Smart Keys

Please note: if currently have no smart keys for your vehicle, you would need to get the emergency key blade in your new smart key cut by a locksmith before you can perform the procedure below.

Remove the key blade from your existing or new smart key.
Insert the emergency key blade into the driver door lock cylinder, then turn the key counterclockwise to the unlock position five times within 10 seconds. (on some vehicles, you will need to remove the lock cylinder cap on the driver door handle to access the door lock). The Driver Information Center (DIC) will display READY FOR REMOTE # 2, 3, 4, etc
Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP. The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
Repeat Step 3 two more times. After the third time, all previously known smart keys will no longer work with the vehicle. The remaining smart keys can be re-programmed during the next steps. The DIC display should now show READY FOR REMOTE # 1.
Place the new smart key into the transmitter pocket (inside the center console storage area between the driver and front passenger seats for Cadillac vehicles OR in the front cupholder for Chevrolet and Buick vehicles).
Press ENGINE START/STOP. When the smart key is recognized by the vehicle, the DIC display will show that it is ready to program the next smart key.
Remove the smart key from the transmitter pocket and press the LOCK or UNLOCK button on the smart key.
To program an additional smart key, repeat Steps 6-8.

When all additional smart keys are programmed, press and hold ENGINE START/STOP for approximately 12 seconds to exit programming mode.

Model	Year
Chevrolet Express	2003	Programming Instructions
Chevrolet Express	2004	Programming Instructions
Chevrolet Express	2005	Programming Instructions
Chevrolet Express	2006	Programming Instructions
Chevrolet Express	2007	Programming Instructions
Chevrolet Express	2008	Programming Instructions
Chevrolet Express	2009	Programming Instructions
Chevrolet Express	2010	Programming Instructions
Chevrolet Express	2011	Programming Instructions
Chevrolet Express	2012	Programming Instructions
Chevrolet Express	2013	Programming Instructions
Chevrolet Express	2014	Programming Instructions
Chevrolet Express	2015	Programming Instructions
Chevrolet Express	2016	Programming Instructions
Chevrolet Express	2017	Programming Instructions

Model	Year
Chevrolet Express 1500	1999	Programming Instructions
Chevrolet Express 1500	2000	Programming Instructions
Chevrolet Express 1500	2001	Programming Instructions
Chevrolet Express 1500	2002	Programming Instructions
Chevrolet Express 1500	2003	Programming Instructions
Chevrolet Express 1500	2004	Programming Instructions
Chevrolet Express 1500	2005	Programming Instructions
Chevrolet Express 1500	2006	Programming Instructions
Chevrolet Express 1500	2007	Programming Instructions
Chevrolet Express 1500	2008	Programming Instructions
Chevrolet Express 1500	2009	Programming Instructions
Chevrolet Express 1500	2010	Programming Instructions
Chevrolet Express 1500	2011	Programming Instructions
Chevrolet Express 1500	2012	Programming Instructions
Chevrolet Express 1500	2013	Programming Instructions
Chevrolet Express 1500	2014	Programming Instructions

2008 Chevrolet Express 1500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2008 Chevrolet Express 1500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2009 Chevrolet Express 1500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2009 Chevrolet Express 1500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2010 Chevrolet Express 1500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2010 Chevrolet Express 1500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2011 Chevrolet Express 1500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2011 Chevrolet Express 1500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2012 Chevrolet Express 1500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2012 Chevrolet Express 1500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

Model	Year
Chevrolet Express 2500	1999	Programming Instructions
Chevrolet Express 2500	2000	Programming Instructions
Chevrolet Express 2500	2001	Programming Instructions
Chevrolet Express 2500	2002	Programming Instructions
Chevrolet Express 2500	2003	Programming Instructions
Chevrolet Express 2500	2004	Programming Instructions
Chevrolet Express 2500	2005	Programming Instructions
Chevrolet Express 2500	2006	Programming Instructions
Chevrolet Express 2500	2007	Programming Instructions
Chevrolet Express 2500	2008	Programming Instructions
Chevrolet Express 2500	2009	Programming Instructions
Chevrolet Express 2500	2010	Programming Instructions
Chevrolet Express 2500	2011	Programming Instructions
Chevrolet Express 2500	2012	Programming Instructions
Chevrolet Express 2500	2013	Programming Instructions
Chevrolet Express 2500	2014	Programming Instructions
Chevrolet Express 2500	2015	Programming Instructions
Chevrolet Express 2500	2016	Programming Instructions
Chevrolet Express 2500	2017	Programming Instructions

2008 Chevrolet Express 2500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2008 Chevrolet Express 2500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2009 Chevrolet Express 2500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2009 Chevrolet Express 2500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2010 Chevrolet Express 2500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2010 Chevrolet Express 2500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

Model	Year
Chevrolet Express 3500	1999	Programming Instructions
Chevrolet Express 3500	2000	Programming Instructions
Chevrolet Express 3500	2001	Programming Instructions
Chevrolet Express 3500	2002	Programming Instructions
Chevrolet Express 3500	2003	Programming Instructions
Chevrolet Express 3500	2004	Programming Instructions
Chevrolet Express 3500	2005	Programming Instructions
Chevrolet Express 3500	2006	Programming Instructions
Chevrolet Express 3500	2007	Programming Instructions
Chevrolet Express 3500	2008	Programming Instructions
Chevrolet Express 3500	2009	Programming Instructions
Chevrolet Express 3500	2010	Programming Instructions
Chevrolet Express 3500	2011	Programming Instructions
Chevrolet Express 3500	2012	Programming Instructions
Chevrolet Express 3500	2013	Programming Instructions
Chevrolet Express 3500	2014	Programming Instructions
Chevrolet Express 3500	2015	Programming Instructions
Chevrolet Express 3500	2016	Programming Instructions
Chevrolet Express 3500	2017	Programming Instructions

2008 Chevrolet Express 3500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2008 Chevrolet Express 3500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2009 Chevrolet Express 3500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2009 Chevrolet Express 3500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2010 Chevrolet Express 3500 Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2010 Chevrolet Express 3500 Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

Model	Year
Chevrolet HHR	2006	Programming Instructions
Chevrolet HHR	2007	Programming Instructions
Chevrolet HHR	2008	Programming Instructions
Chevrolet HHR	2009	Programming Instructions
Chevrolet HHR	2010	Programming Instructions
Chevrolet HHR	2011	Programming Instructions

Model	Year
Chevrolet Impala	2001	Programming Instructions
Chevrolet Impala	2002	Programming Instructions
Chevrolet Impala	2003	Programming Instructions
Chevrolet Impala	2004	Programming Instructions
Chevrolet Impala	2005	Programming Instructions
Chevrolet Impala	2006	Programming Instructions
Chevrolet Impala	2007	Programming Instructions
Chevrolet Impala	2008	Programming Instructions
Chevrolet Impala	2009	Programming Instructions
Chevrolet Impala	2010	Programming Instructions
Chevrolet Impala	2011	Programming Instructions
Chevrolet Impala	2012	Programming Instructions
Chevrolet Impala	2013	Programming Instructions
Chevrolet Impala	2014	Programming Instructions
Chevrolet Impala	2015	Programming Instructions
Chevrolet Impala	2016	Programming Instructions
Chevrolet Impala	2017	Programming Instructions
Chevrolet Impala	2018	Programming Instructions
Chevrolet Impala	2019	Programming Instructions
Chevrolet Impala	2020	Programming Instructions

2006 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2006 Chevrolet Impala Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2007 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2007 Chevrolet Impala Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2008 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2008 Chevrolet Impala Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2009 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2009 Chevrolet Impala Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2010 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

There are 2 possible procedures for this GM vehicle

NOTE: The instructions will not work for 2011 & Up vehicles. 2011 & Up vehicles require dealer or locksmith programming only

1. THIS PROCEDURE IS FOR VEHICLES WITH THE DRIVER INFORMATION CENTER. IT WILL BE A BUTTON TO THE RIGHT OF THE STEERING WHEEL WITH A VEHICLE ICON AND THE LETTER i.

Insert key and switch the ignition ON (just shy of starting vehicle without cranking engine)
Press vehicle information button until PRESS TO RELEARN REMOTE KEY is displayed.
Press the set/reset button (button will have a check mark) until REMOTE KEY LEARNING ACTIVE is displayed. Vehicle is now in programming mode.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2. THIS PROCEDURE IS FOR VEHICLES WITHOUT THE DRIVERS INFORMATION CENTER.

Insert key into the ignition and turn to ON (Just shy of starting vehicle without cranking engine).
Press the trip odometer reset button until RELEARN REMOTE KEY is displayed.
Press and hold the trip odometer reset button for approximately 3 seconds until REMOTE KEY LEARNING ACTIVE displays.
Press and hold LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will be heard indicating successful programming.
Repeat step 4. to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.
To exit programming mode turn ignition OFF, remove key and test all remotes.

2010 Chevrolet Impala Key Programming

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key to off and remove the key.
Insert the key to be programmed and turn it to on within 10 seconds of removing the original key.
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light (04-07 GrandPrix, Bonneville, Impala) wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

2017 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2018 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2019 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

2020 Chevrolet Impala Keyless Entry Remote Fob Programming Instructions

If you have a remote flip key, remote portion is programmed during the Key Programming procedure.

FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):

Insert the original, already programmed key in the ignition and start the engine.
After the engine has started, turn the key off and remove the key.
Insert the key to be programmed and turn it to “on” within 10 seconds of removing the original key (do not start the engine).
The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
Repeat steps 1 through 5 if additional keys are to be programmed.

FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):

1. PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:

Place the recognized (already programmed) transmitter in the cupholder.
Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver information Center (DlC) should display “Ready For Remote #2,3,4 or 5.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter Pocket.
Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.

2. PROGRAMMING INSTRUCTIONS IF YOU DON’T HAVE ANY WORKING TRANSMITTERS:

Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays “Remote Learn Pending, Please Wait.”
Wait for ten minutes until the DIC displays “Press Engine Start Button To Learn” and then press the ignition. The DIC displays will again show “Remote Learn Pending, Please Wait.”
Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps. The DIC should now show “Ready For Remote #1.”
Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out to access the transmitter pocket.
Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
Remove the transmitter from the transmitter pocket and press the unlock button.

To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.

Please note: Each vehicle can have up to five transmitters programmed to it.

Get in Touch

Our Policy

Education

We Care

Chevrolet Keyless Entry Remote Fob Programming Instructions Page 1

Keyless Entry Remote Fob Programming Instructions Available for the following Chevrolet models. Click below to select your model.

1999 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2000 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

2001 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

2002 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2003 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2004 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2005 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2006 Chevrolet Astro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2007 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

2007 Chevrolet Avalanche Key Programming

2008 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

2008 Chevrolet Avalanche Key Programming

2009 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

2009 Chevrolet Avalanche Key Programming

2010 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

2010 Chevrolet Avalanche Key Programming

2011 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2011 Chevrolet Avalanche Key Programming

2012 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2012 Chevrolet Avalanche Key Programming

2013 Chevrolet Avalanche Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2002 Chevrolet Avalanche 1500 Keyless Entry Remote Fob Programming Instructions

2003 Chevrolet Avalanche 1500 Keyless Entry Remote Fob Programming Instructions

2004 Chevrolet Avalanche 1500 Keyless Entry Remote Fob Programming Instructions

2005 Chevrolet Avalanche 1500 Keyless Entry Remote Fob Programming Instructions

2006 Chevrolet Avalanche 1500 Keyless Entry Remote Fob Programming Instructions

2003 Chevrolet Avalanche 2500 Keyless Entry Remote Fob Programming Instructions

2004 Chevrolet Avalanche 2500 Keyless Entry Remote Fob Programming Instructions

2005 Chevrolet Avalanche 2500 Keyless Entry Remote Fob Programming Instructions

2006 Chevrolet Avalanche 2500 Keyless Entry Remote Fob Programming Instructions

1999 Chevrolet Blazer Keyless Entry Remote Fob Programming Instructions

2000 Chevrolet Blazer Keyless Entry Remote Fob Programming Instructions

2001 Chevrolet Blazer Keyless Entry Remote Fob Programming Instructions

2002 Chevrolet Blazer Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2003 Chevrolet Blazer Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2004 Chevrolet Blazer Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2005 Chevrolet Blazer Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2010 Chevrolet Camaro Keyless Entry Remote Fob Programming Instructions

2011 Chevrolet Camaro Keyless Entry Remote Fob Programming Instructions

2012 Chevrolet Camaro Keyless Entry Remote Fob Programming Instructions

2013 Chevrolet Camaro Keyless Entry Remote Fob Programming Instructions

2014 Chevrolet Camaro Keyless Entry Remote Fob Programming Instructions

2015 Chevrolet Camaro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2015 Chevrolet Camaro Key Programming

2016 Chevrolet Camaro Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2016 Chevrolet Camaro Key Programming

2011 Chevrolet Captiva Sport Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2012 Chevrolet Captiva Sport Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2013 Chevrolet Captiva Sport Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2014 Chevrolet Captiva Sport Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2015 Chevrolet Captiva Sport Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2015 Chevrolet Captiva Sport Key Programming

2000 Chevrolet Cavalier Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2001 Chevrolet Cavalier Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

2002 Chevrolet Cavalier Keyless Entry Remote Fob Programming Instructions

Find A Locksmith

Keyless Entry Remote Fob Programming Instructions Available for the following Chevrolet models.
Click below to select your model.